|
Post by bernieb on May 26, 2022 16:08:50 GMT -5
Any ideas what might be going on here? I've deleted my green several times and started from scratch to have this happen every time if I place it back on this area.
|
|
|
Post by ErixonStone on May 27, 2022 6:28:30 GMT -5
I'm sorry, what exactly is the issue you're pointing out here? Is it that one clump of grass in the fringe?
|
|
|
Post by sroel908 on May 27, 2022 7:04:15 GMT -5
I'm sorry, what exactly is the issue you're pointing out here? Is it that one clump of grass in the fringe? I'm assuming he's referring to how the grid looks? bernieb - I have not seen that before, and am not sure why it would be doing that. Only thing I can think of is water plane, so maybe raise up the ground near there and see if that helps? Also, it almost seems as though it is thinking that part of the green is fringe...perhaps messing around with fridge width could help.
|
|
|
Post by Celtic Wolf on May 27, 2022 9:33:16 GMT -5
A couple of questions, did you widen the green fringe and secondly how did you create your green? You get a faded green grid on the fringe and it looks as if the part in question has been splined separately from the green.
|
|
|
Post by scootmcgoot on May 31, 2022 7:23:22 GMT -5
I’ve also seen this happen when the green is too big.
|
|
|
Post by bernieb on May 31, 2022 10:05:06 GMT -5
After continuously messing with it, deleting, and re-splining the green, I found a way to correct it. I dont know why this kept happening on this specific green, but I had to go into the "Hole 2 Green Settings" and slide the Fringe Width down to 0, then back to the normal setting. I've never even used that setting before and I dont know why this specific area of the course/green kept giving me the same issue.
|
|
|
Post by trailducker on May 31, 2022 11:53:12 GMT -5
After continuously messing with it, deleting, and re-splining the green, I found a way to correct it. I dont know why this kept happening on this specific green, but I had to go into the "Hole 2 Green Settings" and slide the Fringe Width down to 0, then back to the normal setting. I've never even used that setting before and I dont know why this specific area of the course/green kept giving me the same issue. Wait there’s setting per hole? You can have different fringe widths on different holes? If I’m understanding this, where is this sorcery?
|
|
|
Post by bernieb on Jun 1, 2022 15:13:57 GMT -5
After continuously messing with it, deleting, and re-splining the green, I found a way to correct it. I dont know why this kept happening on this specific green, but I had to go into the "Hole 2 Green Settings" and slide the Fringe Width down to 0, then back to the normal setting. I've never even used that setting before and I dont know why this specific area of the course/green kept giving me the same issue. Wait there’s setting per hole? You can have different fringe widths on different holes? If I’m understanding this, where is this sorcery? Take a look at my screenshots and you'll notice the "Hole 2 Green Settings." It populates when you hover over the Green.
|
|
|
Post by trailducker on Jun 1, 2022 16:56:00 GMT -5
Wait there’s setting per hole? You can have different fringe widths on different holes? If I’m understanding this, where is this sorcery? Take a look at my screenshots and you'll notice the "Hole 2 Green Settings." It populates when you hover over the Green. Ohhh geez I never noticed you can change that. Does it allow you to change fringe width on one hole compared to the others? I always thought what you do in the Course Settings menu was all over the course
|
|